 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MOS FET Relay MOS FET Relay for Switching Minute and Analog Signals in Low-profile Case (2.1 mm in height) s Switches minute signals and analog signals. s Switches AC and DC. s Load voltage: 60 V. s Low ON-resistance: 2 . s UL/CSA approval pending. G3VM-S1 R s Appearance OMRON logo Model name LOT No. Note: "G3VM" is not printed on the actual product. Ordering Information Contact form SPST-NO Terminals Surface-mounting terminals Load voltage (peak value) 60 VAC Model G3VM-S1 G3VM-S1(TR) Number per stick 100 ----2,500 Taping quantity Application Examples * Electronic automatic exchange systems * Measuring control systems * Datacoms 1 G3VM-S1 G3VM-S1 Specifications s Absolute Maximum Ratings (Ta = 25C) Item LED forward current LED forward current reduction rate Repetitive peak LED forward current LED reverse voltage Permissible loss Connection temperature Load voltage Continuous load current Symbol IF Rating 50 mA -0.5 mA/C 1A 5V 50 mW 125C 60 V 300 mA 0.9 A 180 mW -3 mA/C 230 mW 1,500 Vrms 5 x 10 -55 to 100C -40 to 85C 10 Conditions --Ta 25C 100-s pulses, 100 pps ------AC peak value ------Ta 25C --AC, 1 min VS = 500 V, ambient operating humidity 60% ----- IF/C IFP VR Pin TJ VOFF IO Ipeak Pout Input Output Peak load current Output loss ON current reduction rate ION/C PT VI-O RI-O Tstg Ta Total permissible loss Dielectric strength between I/O terminals (See note.) Insulation resistance Storage temperature Ambient operating temperature Note s The dielectric strength between I/O terminals was measured with voltage applied to all of the input pins and all of the output pins. Electrical Performance (Ta = 25C) Item LED forward current Symbol VF IR CT RON ILEAK TON TOFF CI-O Minimum 1.0 V --------------Standard 1.15 V --30 pF 1.4 --0.9 ms 0.1 ms 0.8 pF Maximum 1.3 V 10 A --2 1 A 2 ms 1 ms --VR = 5 V V = 0, f = 1 MHz ION = 300 mA, IF = 5 mA VOFF = 60 V RL = 200 (See note.) VDD = 20 V, IF = 5 mA VS = 0 V, f = 1 MHz Conditions IF = 10 mA Input Reverse current Capacity between terminals Maximum resistance with output ON Current leakage when the relay is closed Output Turn-ON time Turn-OFF time Floating capacity between I/O terminals Note IF 1 2 The operate and release time were measured in the way shown below. 4 3 RL VDD VOUT VOUT TON 90% 10% TOFF IF s Recommended Operating Conditions Item Symbol VDD IF IO Topr --5 mA ---20C Minimum --7.5 mA ----Standard 48 V 25 mA 300 mA 65C Maximum Operating voltage Forward current Continuous load current Operating temperature 2 G3VM-S1 G3VM-S1 Dimensions Note All units are in millimeters unless otherwise indicated. G3VM-S1 4.4 0.25 3.9 0.2 2.1MAX 0.15 0.4 0.1 0.1 2.54 0.25 0.1 0.6 7 0.4 0.3 s Actual Mounting Pad Dimensions (Recommended Value, Top View) G3VM-S1 6 to 6.3 1.2 0.8 2.54 Installation s Terminal Arrangement/Internal Connection (Top View) 4 3 G3VM-S1 1 2 3 G3VM-S1 G3VM-S1 Precautions !WARNING Be sure to turn OFF the power when wiring the Relay, otherwise an electric shock may be received. Surge Voltage Protection Circuit Example 1 2 3 6 5 4 !WARNING Do not touch the charged terminals of the SSR, otherwise an electric shock may be received. !Caution Do not apply overvoltage or overcurrent to the I/O circuits of the SSR, otherwise the SSR may malfunction or burn. Protection from Spike Voltage on the Output Terminals If a spike voltage exceeding the absolute maximum rated value is generated between the output terminals, insert a C-R snubber or clamping diode in parallel to the load as shown in the following circuit diagram to limit the spike voltage. Spike Voltage Protection Circuit Example 1 2 6 5 4 !Caution Be sure to wire and solder the Relay under the proper soldering conditins, otherwise the Relay in operation may generate excessive heat and the Relay may burn. s Correct Use 3 Typical Relat Driving Circuit Examples C-MOS C-MOS R1 VF Vcc 1 2 3 VIN VOL/OH 6 5 4 1 2 3 6 5 4 Load Unused Terminals (6-pin only) Terminal 3 is connected to the internal circuit. Do not connect anything to terminal 3 externally. Pin Strength for Automatic Mounting Transistor Vcc In order to maintain the characteristics of the relay, the force imposed on any pin of the relay for automatic mounting must not exceed the following. A R1 B 10 to 100k VF 1 2 3 6 5 4 Load In direction A: 1.96 N max. In direction B: 1.96 N max. VIN VOL/OH Load Connection Do not short-circuit the input and output terminals while the relay is operating or the relay may malfunction. AC Connection 1 2 3 6 5 4 or Load AC DC DC or Use the following formula to obtain the LED current limiting resistance value to assure that the relay operates accurately. R1 = VCC - VOL - VF (ON) 5 to 20 mA Use the following formula to obtain the LED forward voltage value to assure that the relay releases accurately. DC Single Connection 1 2 3 1 2 3 6 5 4 6 5 4 Load DC Load DC VF (OFF) = VCC - VOH < 0.8 V Protection from Surge Voltage on the Input Terminals If any reversed surge voltage is imposed on the input terminals, insert a diode in parallel to the input terminals as shown in the following circuit diagram and do not impose a reversed voltage value of 3 V or more. 4 G3VM-S1 DC Parallel Connection 1 2 3 6 5 4 Load DC G3VM-S1 Solder Mounting Maintain the following conditions during manual or reflow soldering of the relays in order to prevent the temperature of the relays from rising. 1. Pin Soldering Solder each pin at a maximum temperature of 260C within 10 s. 2. Reflow Soldering a. Solder each pin at a maximum temperature of 260C within 10 s. b. Make sure that the ambient temperature on the surface of the resin casing is 240C max. for 10 s maximum. c. The following temperature changes are recommendable for soldering. Temperature (C) 240 5C/s max. 210 150 60 s 10 s max. 30 s max. Time (sec) 5 G3VM-S1 G3VM-S1 6 G3VM-S1 G3VM-S1 7 G3VM-S1 G3VM-S1 ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. K116-E1-1 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Electronics Components Company Electronic & Mechanical Components Division H.Q. Low Signal Relay Division 2-1, 2-chome, Nishikusatsu, Kusatsu-city, Shiga-pref., 525-0035 Japan Phone: (81)77-565-5481 Fax: (81)77-565-5581 Printed in Japan 0201-2M (0201) (A) 8 |
Price & Availability of G3VM-S1TR
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |